Sections All products
Use checkboxes for multiple choice, click a name to enter one section only.
Updating results...
Form Factors All form-factors
Use checkboxes for multiple choice, click a name to enter one section only.
  • Select all / Select none

Updating results...
Vendor All vendors
Use checkboxes for multiple choice, click a name to enter one section only.
  • Select all / Select none

Updating results...
JANUS-MM-4LP-XT JANUS-MM-4LP-XT PC/104-Plus Quad Isolated CAN Module with 24 Digital I/O High Performance CAN Functionality The Janus-MM-4LP-XT I/O module offers two or four CANbus 2.0B ports with opto-isolation plus 24 digital I/O lines. Models are available in both the PC/104-Plus and PC/104 form factors. An FGPA core houses the CAN controller logic and provides data rates up to 1Mbps. Each port supports standard and extended frames as well as expanded TX and RX message queues for enhanced performance. Each port has its own combination isolator and transceiver chip. The Janus-MM-4LP-XT fits a wide variety of rugged and on-vehicle embedded serial I/O application needs. Digital I/O Janus-MM-4LP-XT offers 24 programmable digital I/O lines organized as three 8-bit digital I/O ports. Rugged Design Janus-MM-4LP-XT was designed with harsh applications in mind including latching connectors to further improve reliability. Extended temperature operation of −40°C to +85°C is tested and guaranteed. The module is compatible with MIL-STD-202G shock and vibration specifications. Key Features All four CAN ports on the Janus-MM-4LP-XT are driven from an FPGA-based CAN 2.0 bus controller core which provides full CAN2.0B functionality. Each port has an Analog Devices combination isolation and transceiver chip, independently isolating it from the host system and other ports to eliminate sensitivity to noise and ground shifts in the network. The product has several jumper configurable options including CAN termination and bias. The digital I/O logic level and pull-up / pull-down resistors are also jumper configurable. For additional ruggedization, zero ohm jumper-bypass resistors can be installed in any configuration. Software Support Janus-MM-4LP-XT comes with a basic CAN driver for Windows 7, XP and Linux 2.6. The driver supports dual-independent and dual-redundant modes. PCIEcan 2xHS v2 PCIEcan 2xHS v2 High speed CAN network card with 2 high speed CAN channels Kvaser PCIEcan 2xHS v2 is a highly integrated, high speed controller area network (CAN) network card that adds two high speed (ISO 11898-2 compliant) CAN channels to any standard computer board with PCI Express capability. At 86 x 69 mm, this has a smaller form factor and lower profile than the Kvaser PCIEcan 2xHS and includes a DS9 to 2xDS9 splitter cable. Offering silent mode, error frame detection/generation and an on-board buffer, this add-on board fits many embedded data acquisition systems and is CAN FD compliant.
Mini PCI Express 2xHS Mini PCI Express 2xHS Mini PCI Express add-on board with 2 high speed CAN channels Measuring 30 x 51mm, the Kvaser Mini PCI Express 2xHS is a highly integrated CAN (controller area network) add-on board that adds two high speed CAN channels to any standard computer board with mini PCI Express capability. Offering silent mode, error frame detection and an on-board buffer, the small form factor board fits any embedded data acquisition systems, but is particularly suitable for fleet management to monitor key parameters such as fuel economy, engine speed, braking and accelerator pressure, and gearshift patterns. PCIEcan 4xHS PCIEcan 4xHS High speed CAN network card with 4 high speed CAN channels Kvaser PCIEcan 4xHS is a highly integrated, high speed CAN network card that adds four high speed controller area network (CAN) channels to any standard computer board with PCI Express capability. Offering silent mode, error frame detection and an on-board buffer, this small form factor add-on board fits many embedded data acquisition systems and is CAN-FD ready. Features: CAN FD ready Quick and easy plug-and-play installation Supports High Speed CAN (ISO 11898-2) Supports both 11-bit (CAN 2.0A) and 29-bit (CAN 2.0B active) identifiers Low profile card (86×69mm) allows ultra-compact systems Implements Kvaser's CAN IP in an FPGA, resulting in high max message rate Four CAN Hi-Speed channels in a single 26-pin HDD-SUB CAN connector The HD26 splitter connects tothe CAN bus via four 9-pin DSUB connectors Four yellow LEDs that indicate when a CAN message was received orsent Fully compatible with J1939, CANopen, NMEA 2000 and DeviceNet Supports silent mode for analysis tools listens to the bus without interfering Detection and generation of error frames and remote frames Designed for standard and industrial computers Galvanically isolated CAN bus drivers Wide operating temperature of 0°C to +85°C Supports the Kvaser Linx Software: Documentation, software and drivers can bedownloaded for free atwww.kvaser.com/downloads Kvaser CANLIB SDK isafree resource that includes everything you need to develop software for the Kvaser CAN interfaces. Includes full documentation and many program samples, written in C, C++, C#, Delphi, and Visual Basic All Kvaser CAN interface boards share acommon software API. Programs written for one interface type will run without modifications onthe other interface types! J2534 Application Programming Interface available RP1210A Application Programming Interface available On-line documentation in Windows HTML-Help and Adobe Acrobat format
PCI104 PCI104 PCI-104 CAN interface board with 2 channels Compact and self-stacking, the Kvaser PCI104 board complies with the flexible PCI-104 specification. The Kvaser PCI104 board represents a dual channel CAN interface, with a high performance microcontroller onboard. Hardware * Compliant with the PCI-104 specification * Stack-through connector * On-board 16-bit microcontroller * Communicates with the PC through a fast DPRAM * CAN Controller from Renesas (M16C) * Supports CAN 2.0 A and 2.0 B (active) * Supports Silent Mode * High-speed ISO 11898 compliant driver circuits, supports bit rates up to 1 Mbit/s * Galvanic isolation between the CAN-controller and the CAN-driver * CAN oscillator frequency: 16 MHz * Quick and easy plug-and-play installation * Dimensions 91 x 96 mm (approx. 3.6 x 3.8 in.) * Interfaces the CAN bus with IDC Headers * Wide temperature range, -40°C - +85°C PCIEcan PCIEcan CAN/PCI Express interface boards with 2 channels The Kvaser PCIEcan is a CAN interface board, with one or two CAN channels, for PCI Express bus systems. Galvanically isolated CAN bus drivers to protect the hardware. * Supports PCI Express x1 * Designed for standard and industrial computers * Quick and easy plug and play installation * Hardware compatible with the PCIcanx and PCIcan product families * I/O mapped to enable quick reaction times * Support CAN 2.0 A and 2.0 B (active) * Detection and generation of error frames and remote frames * SJA1000 CAN Controllers from Philips, with 64-byte receive FIFO * Galvanically isolated CAN bus drivers * Supports Silent Mode * Dimensions 122 x 103 mm (approx. 4.8 x 4.0 in.) * High-speed ISO 11898 compliant driver circuits * Interfaces the CAN bus with DSUB CAN connectors. Pin assignment according to CiA-DS102 * 16 MHz CAN oscillator frequency * Wide temperature range, -40°C - +85°C * Supports the Kvaser Linx * Patent Number: US 5,696,911, SE 501984, DE 19514696
PC104+ PC104+ PC/104-Plus CAN interface board with 2 channels Compact and self-stacking, the Kvaser PC104+ board complies with the flexible PC/104-Plus specification. Allowing embedded system designers to substantially reduce development costs and time. The Kvaser PC104+ board represents a dual channel CAN interface, with a high performance microcontroller onboard. Hardware * Compliant with the PC/104-Plus specification * Stack-through connector * On-board 16-bit microcontroller * Communicates with the PC through a fast DPRAM * CAN Controller from Renesas (M16C) * Supports CAN 2.0 A and 2.0 B (active) * Supports Silent Mode * High-speed ISO 11898 compliant driver circuits, supports bit rates up to 1 Mbit/s * Galvanic isolation between the CAN-controller and the CAN-driver * CAN oscillator frequency: 16 MHz * Quick and easy plug-and-play installation * Dimensions 91 x 96 mm (approx. 3.6 x 3.8 in.) * Interfaces the CAN bus with IDC Headers or 9 pin DSUB connectors * Wide temperature range, -40°C - +85°C Note: the ISA bus connector is a pass-through connector. The card does not use the ISA bus. It is PCI only PCIcanx PCIcanx CAN/PCI interface boards with 1, 2 or 4 channels Kvaser PCIcanx product family is a family of CAN/PCI interface boards and comprises three members: Kvaser PCIcanx 4xHS, PCIcanx HS/HS and PCIcanx HS. The Kvaser PCIcanx boards fits in both PCI-X and PCI bus systems. Galvanically isolated CAN bus drivers to protect the hardware. * Compliant with PCI 2.3 * The board fits in both 3.3V PCI-X and 3.3V and 5V PCI busses * Completely compatible with our PCIcan boards. * Dimensions 140 x 100 mm (approx. 5.5 x 4 in.) * I/O mapped * Quick and easy plug-and-play installation * SJA1000 CAN Controllers from Philips, with 64-byte receive FIFO * Supports CAN 2.0 A and 2.0 B (active) * High-speed ISO 11898 compliant driver circuits * Interfaces the CAN bus with DSUB CAN connectors * Pin assignment according to CiA-DS102 * 16 MHz CAN oscillator frequency * Galvanic isolation between the CAN-controller and the CAN-driver * Wide temperature range, -40°C - +85°C
PCIcanx II PCIcanx II CAN/PCI interface boards with 1 or 2 channels Kvaser PCIcanx II is a high-performance CAN/PCI interface board and comprises two members: PCIcanx II HS/HS and PCIcanx II HS. Kvaser PCIcanx II HS is delivered with a free of charge low profile bracket. The Kvaser PCIcanx II boards fits in both PCI-X and PCI bus systems. Galvanically isolated CAN bus drivers to protect the hardware. Hardware Specifications * Compliant with PCI 2.3 * The board fits in both 3.3V PCI-X and 3.3V and 5V PCI busses * Fully software compatible with the discontinued PCIcan II boards * On-board 16-bit microcontroller * Dimensions 120 x 95 mm (approx. 4.5 x 4 in.) * Communicates with the PC through a fast DPRAM * Quick and easy plug-and-play installation - no switches. * CAN Controller: Renesas M16C * Supports CAN 2.0 A and 2.0 B (active) * High-speed ISO 11898 compliant driver circuits, supports bit rates up to 1 Mbit/s * Industry-standard 9-pin D-SUB connectors * Pin assignment according to CiA-DS102 * CAN oscillator frequency: 16 MHz * Galvanic isolation between the CAN-controller and the CAN-driver * The Kvaser PCIcanx II family boards can optionally be delivered with exchangeable CAN drivers, supporting e.g. single-wire CAN. PCAN-PCI/104-Express PCAN-PCI/104-Express CAN Interface for PCI/104-Express The PCAN-PCI/104-Express card enables the connection of one, two, or four CAN busses to a PCI/104-Express system. Up to four cards can be stacked together. The CAN bus is connected using a 9-pin D-Sub plug on the slot brackets supplied. There is galvanic isolation of up to 500 Volts between the computer and CAN sides. The card is available as a single, dual, or four-channel version. The package is also supplied with the CAN monitor PCAN-View for Windows® and the programming interface PCAN-Basic.
Show:
Login / Registration
укажите почту
введите пароль
Forgot password?
CAPTCHA
Loading data...
Subscribe to newsletter
specify your contacts