MicroMax's Solutions
MicroMax's Solutions
MicroMax's Solutions
HPSP-XYZ
Triple Programmable Output 240W SFF Power Supply
The HPSP is the product family name of the power supply platform HPSP-x-y-z. The «x» suffix defines the OUT1 voltage, «y» suffix the OUT2 voltage and «z» the OUT3 voltage. In addition to the three main outputs the HPSP also provides a 5VSBY 1A output.
The HPSP is a high power, high performance DC-to-DC converter that supplies three outputs programmable that are programmable up to 24V output and supports an ultra wide input range of 6-50V. The HPSP has two power inputs protected with heavy-duty transient surge stoppers that clamps the input voltage to safe levels. The HPSP is ideal for battery and unregulated input applications. The HPSP uses a flash based microcontroller to supply advanced power management that monitors and controls the operation of the HPSP through a RS232 serial port.
The HPSP is a state-of-the-art Mosfet based design that provides outstanding line and load regulation and high efficiency. The low noise design makes the HPSP ideal for use aboard aircraft or military applications or wherever EMI or RFI must be minimized.
The HPSP advanced power management functions provide timed on/off control of the HPSP, notification of changes to main power and secondary power status.
The HPSP is PC/104 footprint in size of 3.55×3.775 inches with the same mounting holes pattern. However, the HPSP does not include the PC/104 bus connectors. All generated voltages are provided to a removable header. A removable plug allows the HPSP to be easily installed. The RS232 serial port is provided on a 2×5 row pin header.
ATX Compatibility
The HPSP can be configured to be signal compatible to an ATX power supply (The HPSP does not provide −5V, −12V that
standard ATX supplies include but the three outputs can be programmed to provide the standard 3.3V, 5V and 12V).
Advantages
DC to DC converter for embedded applications.
«Load Dump» transient suppression on both main and secondary power supply inputs.
Operates from super wide 6VDC to 50VDC input.
PC/104 size and mounting holes.
Three main programmable outputs OUT1, OUT2 & OUT3. A 1.5A 5VSB outputs is also provided.
Temperature range −40 to 85degC (measured on heat spreader).
Complete with built-in digital temperature sensor.
RS232 serial port for setup, monitoring and control.
Opto-coupled inputs for ignition, and system «shut-down» push-button.
Can be configured to be ATX compatible
TPSi1085
85W Isolated Embedded Power Supply
Tri-M's TPSi1085 is an isolated PC/104-Plus embedded power supply offering 2250V input/output isolation, 6000W transient protection, active input voltage clamping, wide input ranges of +9V to +33V DC, and maximum efficiency 88%. This rugged design operates in an extended temperature range from -40°C to +85°C (-40°F to +185°F), and features quick-disconnect terminal socket plugs for simple installation.
Galvanically isolated and short circuit protected, the TPSi1085 offers two standard outputs of +3.3V @ 8A and +5V @17A with total combined power of 85W. This isolated power solution also provides remote shutdown functionality, power failure signaling and three dual colour LED status indicators. For PC/104-Plus connectivity, there are also 8bit, 16bit, and PCI headers with passthrough/non-passthrough bus versions available.
For applications requiring a clean isolated power, the TPSi1085 is the perfect solution. This high density, small form factor, and unprecedented SWaP (size, weight, and performance) board is the perfect design for military, aerospace, transportation, and industrial applications.
Advantages
High efficiency
Extended temperature operation
Rugged design
High voltage isolation
Transient supression
Clean and filtered power for the PC/104 bus
Power/OS
TPSi2100
100W Isolated Power Supply
Tri-M's TPSi2100 is an isolated PC/104-Plus power solution, designed for embedded applications requiring isolation and clean power in rugged environments.
With wide-range input voltages, transient suppression, galvanic isolation, and pluggable terminal mating plugs, this rugged design is ideal for any industrial application.
For applications requiring a clean isolated power, the TPSi2100 is the perfect solution. This high density, small form factor, and unprecedented SWaP (size, weight, and performance) board is the perfect design for military, aerospace, transportation, and industrial applications.
Advantages
High efficiency
Extended temperature operation
Rugged design
High voltage isolation
2250V input/output isolation
6000W transient suppression
Active input voltage clamping
Reverse polarity protection
Clean and filtered power for the PC/104 bus
Power/OS
DA104
Hard Drive and Compact Flash adapters for PC/104 stacks
The DA104 provides a convenient means of integrating a 2.5″ IDE hard drive, M‑Systems CompactFlash, or M‑Systems IDE2000 Flash Disk onto a PC/104 «stack». Connection of the drive to the host CPU IDE port is supported by a standard 40 pins ribbon cable.
The 5VDC power for the drives is supplied either though the PC/104 bus, or 2 positions screw terminal. For additional memory, a second 2.5″ hard drive or IDE2000 Flash Disk can be mounted to the underside of the module.
IO104-60IN
PC/104 Digital IO Module
The IO104-60IN board is a a simple PC/104 opto isolated input card featuring 60 inputs.
The inputs are accessed through I/O memory reads. The 60 inputs are grouped as seven sets of eight inputs, and one set of four inputs.
Each group of inputs is accessed through an I/O memory address, which is an offset from the base decode address.
IR104
PC104 Rugged Relay Board
The IR104 is a PC104 rugged industrial relay module featuring 20 optoisolated digital inputs and 20 relay outputs, sufficient for many industrial control applications. Each input can accept either AC or DC voltages with a range of 3-24V and are accessed through a 40-pin header that mates with a standard ribbon cable. The 20 SPST (Form A) relays have a long lifetime (20,000,000 operations, 100,000 at full load) and quick actuation time (10ms max operate, 5ms release). The relays are supplied with a contact rating of 250VAC or 30VDC @ 5A giving the IR104 the ability to directly control switches for small motors or solenoids. The relays are in the open state when deactivated / powered off.
To allow for quick and convenient installation, a pair of 20-position detachable terminal blocks accept wire sizes of 14-28AWG. The IR104 is a compact design measuring 3.550″ x 3.775″ with a maximum component height of 0.492″. A 16-bit PC/104 BUS is included to allow for easy integration into embedded systems or to allow for up to 4 IR104 modules to be stacked together.
The IR104 operates on single 5VDC, has a −25° to +70°C operating temperature range and is now RoHS compliant.
ISA104
ISA bus extender for PC/104 stacks
This passive extender card allows developers to mount an 8 or 16-bit PC/104 card into a standard ISA bus PC system, avoiding the need for a dedicated PC/104 stack for development work.
The adapter is equipped with a stack-through connector so the test card can be installed on either side enabling probing on the front or the back. A secondary PC/104 location allows addition of troubleshooting modules.
Standard Usage
Simply stack the test PC/104 card onto the adapter's PC/104 connectors and insert the adapter into the host system's ISA slot. No additional configuration is required
PC104-T
16 bit AC termination modules for the PC/104 bus
AC termination provides increased noise immunity for mobile PC/104 applications. Vehicle environments are notoriously noisy. EMI, voltage spikes, and other noise sources can interfere with proper bus operation and corrupt data transfers.
The AC termination board shown here plugs onto the end of the PC/104 stack to quiet the bus signals and increase system integrity more effectively than simple resistive termination. It can be used with any PC/104 system, with or without a PC/104 power supply module.
When ordering the HE104 power supply modules, order option-T, and the bus termination components will be mounted right on the circuit board module without taking up additional height on the PC/104 stack.
Postcode104/ISA
Debugging tool with PC/104 header
The Postcode104/ISA is a ‘Power On Self Test’ (POST) code board that is an excellent microprocessor based debugging tool. Featuring both a PC/104 bus and an ISA connector, POST codes can be toggled through to quickly identify any errors.
Plugging the module onto a Single Board Computer’s PC/104 or ISA BUS provides a ‘Power On Self Test’ at system startup. POSTcodes are captured from port 80h/84h and saved in EEPROM memory. The Postcode104/ISA has two hundred fifty POSTcodes stored in a FIFO buffer that can be viewed via the onboard LED display. PREV and NEXT buttons on the module allow the user to toggle through the list of POSTcodes to quickly identify errors. A serial output is provided for printing with time stamped code history. Features reset, polling, and storage modes.
The Postcode104/ISA is a standalone tool measuring 3.75″ x 1.75″ that runs off power supplied by the computer Bus.
VersaTainer
Rugged PC/104 or EBX Enclosure
The VersaTainer (VT104) is a rugged EBX and PC/104 enclosure system constructed of .125″ aluminum and designed for hostile and mobile environments. It features a dual system of shock and vibration isolation which comprises of internal rubber corner rails absorb high-frequency vibrations, while the entire enclosure is mounted on the host platform with a thick rubber pad which absorbs low-frequency G-forces. The rubber pad may be removed for optional mounting solutions such as hard mounting, flange endcap, or fluidic mount assembly.
The VersaTainer is capable of housing PC/104 and EBX payloads. For PC/104, the stack mounts axially along the entire length of the enclosure body. For EBX, An optional EBX mounting plate (VT-EBX) is available to mount the SBC to be horizontally with ample room for several PC/104 accessory cards to be installed. Accessory modules such as hard drives larger than 3.550″ x 3.775″ can be mounted to an optional septum plate that installs vertically into rails that run the length of the enclosure. For smaller items, an optional PC/104-size aluminum plate allows for direct mounting in the PC/104 stack.
The VersaTainer enclosure cross section measures 7.10″ wide by 5.70″ high (not including mounting pad) and is available in standard lengths from 4″ to 12″ and custom lengths up to 48″. Each VersaTainer is available as a kit with mounting accessories. Blank and pre-designed endcaps are available from stock, or the customer may design their own cutouts using one of our VersaTainer endcap templates. These rugged enclosures have been protecting PC104 systems all over the world in the harshest environments the mining, transportation, military, and aerospace industries have to offer. The VersaTainer and its standard accessories are RoHS compliant.
