PCIcanx II
PCIcanx II CAN/PCI interface boards with 1 or 2 channels Kvaser PCIcanx II is a high-performance CAN/PCI interface board and comprises two members: PCIcanx II HS/HS and PCIcanx II HS. Kvaser PCIcanx II HS is delivered with a free of charge low profile bracket. The Kvaser PCIcanx II boards fits in both PCI-X and PCI bus systems. Galvanically isolated CAN bus drivers to protect the hardware. Hardware Specifications * Compliant with PCI 2.3 * The board fits in both 3.3V PCI-X and 3.3V and 5V PCI busses * Fully software compatible with the discontinued PCIcan II boards * On-board 16-bit microcontroller * Dimensions 120 x 95 mm (approx. 4.5 x 4 in.) * Communicates with the PC through a fast DPRAM * Quick and easy plug-and-play installation - no switches. * CAN Controller: Renesas M16C * Supports CAN 2.0 A and 2.0 B (active) * High-speed ISO 11898 compliant driver circuits, supports bit rates up to 1 Mbit/s * Industry-standard 9-pin D-SUB connectors * Pin assignment according to CiA-DS102 * CAN oscillator frequency: 16 MHz * Galvanic isolation between the CAN-controller and the CAN-driver * The Kvaser PCIcanx II family boards can optionally be delivered with exchangeable CAN drivers, supporting e.g. single-wire CAN.
DB9-Power Inlet
DB9-Power Inlet Power injector with one female and one non‑connected male D-SUB9 connector Kvaser DB9-Power Inlet is a power injector for CAN buses from a DC power jack into one female D-SUB9 connector. The Kvaser DB9-Power Inlet also has one unpowered male D-SUB9 connector for connecting to the CAN network. The Kvaser DB9-Power Inlet provides a simple and safe way to supply Kvaser interfaces on a development board, as well as powering interface devices without internal power, such as Kvaser’s Blackbird and Memorator series. Major Features: Acts as a power injector with one female and one non-connected male D-SUB9 connector Connects to power supply using a standard 2.0 mm DC power connector. A complementary 12 V, 1 A power supply is included
Kvaser OBD II Extension Cable
Kvaser OBD II Extension Cable Interface accessory A Kvaser OBDII Extension Cable is an extension cable with a male to female OBD II connector (EAN Numbers 73-03130-00301-9 and 73-03130-00347-7), or connects any Kvaser CAN bus interface with a 9 Pin DSUB connector to a vehicle with an OBD II (J1962) connector (EAN Numbers 73‑03130‑00348‑4 and 73-03130-00349-1). Ordering information EAN Number: 73-03130-00347-7 OBD II (SAE J1962) connector (male - female). Length 2500 mm (98.4in.). EAN Number: 73-03130-00301-9 OBD II (SAE J1962) connector (male - female). Length 5000 mm (196.9in.). EAN Number: 73-03130-00348-4 OBD II (SAE J1962) male connector - 9 pin DSUB female connector. Length 10000 mm (393.7in.). EAN Number: 73-03130-00349-1 OBD II (SAE J1962) male connector - 9 pin DSUB female connector. Length 15000 mm (590.6in.).
PCAN-USB FD
PCAN-USB FD CAN and CAN FD Interface for High-Speed USB 2.0 The CAN FD adapter PCAN-USB FD allows the connection of CAN FD and CAN networks to a computer via USB. A galvanic isolation of up to 500 Volts decouples the PC from the CAN bus. The simple handling and its compact plastic casing make the adapter suitable for mobile applications. The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable. The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD. ISO / Non-ISO CAN FD: Since the first implementations of CAN FD, the protocol has been improved and is now included in the standard ISO 11898-1. The revised CAN FD standard is not compatible with the original protocol. PEAK-System takes this into account by supporting both protocol versions with their CAN FD interfaces. If required, the user can switch to the CAN FD protocol used in the environment by software (Non-ISO and ISO).
Show:
Login / Registration
укажите почту
введите пароль
Forgot password?
By clicking «#SUBMIT_NAME»,
you agree to our Privacy Policy
Loading data...
Subscribe to our newsletter
specify your contacts

By clicking «#SUBMIT_NAME»,
you agree to our Privacy Policy

You have successfully subscribed
Now you can receive newsletters